• 加入收藏设为首页
  • 公司首页
  • 公司简介

  • 新闻动态

  • 产品展示

  • 联系我们

  • 全自动零压线型薄刀纵切压线机
    产品名称:

    全自动零压线型薄刀纵切压线机

    产品描述:

    全自动零压线型薄刀纵切压线机随着刀片磨损和直径减小,分切刀须向下调整,刀锋切过纸板的尺寸在3~5mm范围为宜。

    详细信息

    全自动零压线型薄刀纵切压线机功能特点:

    1、纵切刀、压线轮排单独立伺服控制,排单快速、精确、可靠。

    2、纵切、压线速度变频控制,跟随纸板速度同步调整。

    3、前后两排压线轮配置,压线轮任意组合,实现零压线。

    4、凹压、平压、凸压、偏压四种压线方式。

    5、换单时压线方式自动转换、压线间隙自动调整。

    6、合金钢薄刀纵切,自动磨刀、自动润滑。

    Automatic zero pressure type thin knife slitting line pressing machine features:

    1, slitting knife, single row wire wheel independent servo control, a single row of fast, accurate and reliable.

    2, slitting and creasing speed frequency control, follow the synchronous speed adjustment board.

    3, before and after the two row wire wheel configuration, wire wheel combination, to achieve zero line.

    4, concave pressure, pressure, pressure, bias flat convex four line mode.

    5, for a single line mode automatic conversion, automatic clearance adjusting line.

    6, alloy steel thin knife slitting, automatic sharpening, automatic lubrication.

    全自动零压线型薄刀纵切压线机安全操作及注意事项:

    1、检查机台移动,应能左右移动。

    2、机器运行期间,不允许人员靠近刀轮,以免旋转刀片伤人。

    3、机器停止时,应清理机器上废纸屑。

    4、每班必须停机对机器进行全面清洁保养至少一次,特别是导轨部分要擦干 净,不得留有杂物。

    5、更换薄刀片,压线轮和砂轮等物件必须停机操作。

    6、随着刀片磨损和直径减小,分切刀须向下调整,刀锋切过纸板的尺寸在3~5mm范围为宜。

    7、更换刀片时必须小心刀刃伤人或损坏刀片,上新刀前需清洁刀盘,刀片和压板贴合面。每个刀盘上压紧螺钉拧紧程度应一致,螺钉螺纹不得有损坏。刀片压紧后应检查刀片是否有径向跳动和轴向摆动。刀片在高速运转时禁止人在刀片正面停留或走动。

    Automatic zero pressure type thin knife slitting line pressing machine safety operation and matters needing attention:

    1, check the machine movement, should be able to move around.

    2, the machine running, not allowed to close to the knife wheel, so as not to hurt the rotating blade.

    3, the machine stops, should clean up waste paper machine.

    4, each class must be shut down for the machine to carry out a comprehensive cleaning and maintenance at least once, especially the guide rail part to dry clean, not to leave the debris.

    5, the replacement of thin blade, wire wheel and wheel and other objects must stop operation.

    6, with the blade wear and the decrease of the diameter of cutter blade should be adjusted downward, cut the size of the board should be in the range of 3~5mm.

    7, the replacement of the blade must be careful when the blade wounding or damage to the blade, the new knife before the need to clean the knife set, blade and pressing plate fitting surface. The screw threads must not be damaged in the degree to which the compression screws must be tightened on each cutter head. After the blade is pressed, the blade should be checked for radial pulsation and axial swing. At high speed, the blade is not allowed to stop or move in the front of the blade.

    型号 Model 2000 2300 2500
    最大分切宽度 Max slitting width (mm) 1600 2000 2200
    最小分切宽度 Min slitting width (mm) 140 140 140
    最小压线宽度 Min scoring width (mm) 135 135 135
    压线高度 Scoring height (mm) 0-12 0-12 0-12
    刀片规格 Blade (mm) φ200×122×1.2
    分切压线配压形式 Blade & Scoring Composed Type 5刀8线/6刀10线
    电机功率 Power (KW) 7.9
    外形尺寸 Machine dimension (mm) 3300X1200X2000 3500X1200X2000 3700X1200X2000